Everflon™ PTFE Properties
PTFE PROPERTIES
Understand the material. Design for the conditions.
Explore PTFE properties, processing quality, mechanical behavior, creep, thermal performance, electrical insulation, chemical resistance and fabrication through eight linked technical articles.
Evaluate performance with formulation, processing and test conditions. Use confirmed grade and finished-part data for design and purchasing.
PTFE · 01
Compare PTFE properties and test conditions for material selection.
Everflon™ PTFE belongs to the fluorine-based polymer material system. Related materials also include Everflon™ FEP, Everflon™ PFA, and Everflon™ ETFE. Different fluoropolymers have their own properties and processing characteristics; appropriate materials should be selected according to the actual application.
Everflon™ PTFE: An Engineering Material Combining Multiple Properties
Design requirements should be evaluated in conjunction with processing methods.
Comparison of Typical Performance of Granular Resin and Fine Powder
PTFE · 02
Understand how processing, crystallinity and voids affect PTFE quality.
Everflon™ PTFE is typically manufactured into parts through cold forming and sintering. The reference continuous service temperature for the material is 260°C (500°F); short-term exposure to higher temperatures must be assessed based on actual conditions and cannot be used as a guarantee for the finished product.
Processing Conditions, Determining the Formation of Finished Product Properties
Which PTFE properties are relatively unaffected by processing conditions?
Five quality factors, establishing a link between process and testing
PTFE · 03
Read PTFE tensile, compression and shear data for stress-strain design.
Everflon™ PTFE products are tough and can be flexible in thin sections, while relatively rigid in thick sections. Within the range of −268 to 260°C (−450 to 500°F), PTFE still has mechanical properties that are available but change with conditions. This range does not represent consistent performance of any part under the same load.
General Characteristics: Thin-walled flexible, thick sections have relative stiffness
Preforming, sintering and post-forming: building dense structures
Design considerations and test piece conditions
PTFE · 04
Evaluate PTFE creep, stress relaxation and gasket loading.
Plastic materials will continue to deform over time under continuous load, which is called creep or cold flow. Similar phenomena may occur in metals at high temperatures; and most plastics may still deform significantly even at room temperature or lower temperatures, so the term "cold flow" is used.
Creep and cold flow: time effects under continuous load
Apparent elastic modulus: including usage time in calculation
Tensile creep: comparing total deformation at four temperatures
PTFE · 05
Review PTFE thermal expansion, elastic memory and impact behavior.
The linear thermal expansion of PTFE is shown in Figure 11 and Table 10. Over the transition interval of approximately 18–25°C (65–77°F), the material exhibits a significant volume change of approximately 1.0–1.8%.
Thermal expansion: Precision dimensions must consider the change near room temperature
Volumetric expansion: distinguish coefficients from total changes across the transition
Low temperature performance: strength, toughness and self-lubricating performance
PTFE · 06
Compare PTFE friction, wear and electrical insulation properties.
The hardness of PTFE can be expressed through different test scales. Fillers can increase hardness by about 10–15%, and some of the improvement is retained over a wide temperature range. Generally speaking, when the filling amount is higher, the hardness of the formula will also be higher; spherical or flaky fillers can bring better hardness performance, which still needs to be confirmed according to the formula.
Hardness: Comparison of different measurement scales and filling effects
Friction characteristics of granular resin: speed and pressure will affect
PV limit: the upper limit of continuous operation is not equal to the allowable wear
PTFE · 07
Understand PTFE weathering, chemical resistance, absorption and permeation.
When applications require reliability in outdoor environments, the combination of high temperature resistance, cold resistance and UV resistance can be the basis for PTFE material selection. Antenna bushings in radar and other electronic equipment are examples of applications with such environmental requirements.
Weather resistance: high temperature, low temperature and UV exposure
Other properties: vibration damping at acoustic and ultrasonic frequencies
Chemical resistance: highly inert, still need to pay attention to reaction exception
PTFE · 08
Review PTFE machining, annealing, dimensional measurement and applications.
Machining is a viable manufacturing method for PTFE when the part requires tight tolerances, has a complex shape, or only requires one or two prototypes. Standard operations such as turning, facing, boring, drilling, threading, tapping, reaming and grinding can be used and do not necessarily require special machinery.
Forming and machining: choose according to shape and size requirements
Select processing speed: avoid dimensional deviation caused by heat concentration
Tool shape, sharpness and workpiece support
INQUIRY