EverflonTM FEP
FEP Material Overview and Typical Properties
Understand FEP composition, available forms and typical material properties.
Introduction
FEP (fluorinated ethylene propylene) is a copolymer of hexafluoropropylene and tetrafluoroethylene. Unlike PTFE, FEP can be melt-processed by conventional injection molding and screw extrusion. PFA serves similar applications but can operate at higher temperatures.
FEP can be fabricated into products combining mechanical, chemical, electrical, temperature-resistance and low-friction properties. These engineering notes support evaluation of where and how FEP may be used.
Fabrication can materially affect cost and finished-part performance. Design engineers should work with experienced fabricators. Typical properties are not product specifications or acceptance limits.
Available Product Forms
FEP pellets are used for general molding and extrusion. Higher-molecular-weight, lower-flow resins favor stress-crack resistance where throughput is secondary. Lower-molecular-weight, higher-flow resins support high-speed coating of fine wire.
Suitable standard color concentrates may be used. Specialized forms include coating powders, dispersions and wire-insulation resins.
FEP films are available in different thicknesses for electrical, chemical-contact and release uses. One- or two-sided treatment can improve bondability. Consult Everflon product information for available grades and forms.
Specifications
ASTM D2116 is a relevant FEP resin specification. FEP also appears in industrial and military specifications for tubing, molded parts, films and cable. Compliance must be confirmed for the grade and finished product.
General Properties
FEP combines many PTFE physical, chemical and electrical properties with melt processability. The source material has an upper continuous-use temperature of 205°C (401°F) and is described for cryogenic service below liquid-nitrogen temperature.
The source describes uncontaminated, unpigmented, unfilled material as normally inert to liquid oxygen. LOX use still requires a dedicated compatibility and safety assessment.
Chemical resistance, weatherability and processability support evaluation for valve and pump linings, pipe liners, release materials and elevated-temperature chemical or cryogenic service.
Typical Properties
Molecular weight is a principal grade difference, so toughness and stress-crack resistance can differ. Processing also affects tensile and compressive properties. Electrical and chemical properties are generally similar among the source grades.
| Property | Method | Conditions / units | Typical value |
|---|---|---|---|
| Melt flow rate | ISO 12086/ASTM D2116 | 372°C/5.0 kg;g/10 min | 3–30 |
| Specific gravity | ISO 1183/ASTM D792 | — | 2.15 |
| Tensile strength | ISO 12086/ASTM D638 | 23°C;MPa | 20–34 |
| Elongation at break | ISO 12086/ASTM D638 | 23°C;% | 325 |
| Flexural modulus | ISO 178/ASTM D790 | 23°C;MPa | 550–655 |
| MIT folding endurance | ASTM D2176 (historical standard) | 0.20 mm film; cycles | 5,000–1,000,000 |
| Shore hardness | ISO 868/ASTM D2240 | Shore D | 55 |
| Dielectric constant, 1 MHz | IEC 250/ASTM D150 | — | 2.03 |
| Dielectric constant, 1 GHz | IEC 250/ASTM D2520 | — | 2.03 |
| Dissipation factor, 1 MHz | IEC 250/ASTM D150 | — | 0.00061 |
| Dissipation factor, 1 GHz | IEC 250/ASTM D2520 | — | 0.00094 |
| Dielectric strength | IEC 60243/ASTM D149 | 0.25 mm film; kV/mm | 78 |
| Melting point | ASTM D4591 | °C | 260 |
| Service temperature, 20,000 h | ISO 2578 | °C | 205 |
| Limiting oxygen index | ISO 4589/ASTM D2863 | % | >95 |
| Flammability classification | UL 94 | See note | V-0 |
| Weather resistance | Weather-O-Meter | 2,000 h | No effect |
| Solvent resistance | ASTM D543 | — | Excellent |
| Chemical resistance | Method not stated in source | — | Excellent |
| Water absorption | ASTM D570 | 24 h; % | 0.01 |
Source data, charts and compliance statements concern another manufacturer’s reference material. Renaming a grade does not establish equivalence or measured performance for Everflon FEP 4610. Curves are approximate illustrations, not engineering input. · Product and Properties Handbook: Introduction; Commercially Available Products; Specifications; General Properties; Typical Properties