Blog

Blog

FEP Hardness, Friction and Wear

Nov. 04, 2026

FEP Hardness, Friction and Wear
FEP

EverflonTM FEP 4610

FEP Hardness, Friction and Wear

Understand hardness, friction and the difference between PV limits and useful wear conditions.

Source data, charts and compliance statements concern another manufacturer’s reference material. Renaming a grade does not establish equivalence or measured performance for Everflon FEP 4610. Curves are approximate illustrations, not engineering input.
HARDNESS

Hardness

Three hardness methods were used. Higher-molecular-weight material gave similar results, suggesting little molecular-weight influence within the source's range.

Table 5 | Hardness at 23°C (73°F), source reference
Rockwell RShore DShore A
255696
Different hardness scales are not directly comparable or interchangeable.
FRICTION

Friction

FEP is smooth and slippery, supporting evaluation for unlubricated or minimally lubricated systems. The source reports low friction at low sliding speed and contact pressures above 34 kPa (5 psi).

Friction rises rapidly as speed increases to about 30 m/min (100 ft/min). The source links this behavior to reduced stick-slip and reports no squealing under its low-speed conditions.

Above about 45 m/min (150 ft/min), below the PV limit, speed has less effect. The source also reports decreasing static friction with pressure and little filler effect on its materials' friction coefficient.

Figure 18 | Friction vs sliding speedApproximate source redraw; not measured 4610 data.
Friction
Sliding speed (m/min)
6.9kPa69kPa689kPa

Approximate source redraw; not measured 4610 data.

Figure 19 | Friction vs loadApproximate source redraw; not measured 4610 data.
Friction
Load (kg)
Approximate source redraw; not measured 4610 data.

Approximate source redraw; not measured 4610 data.

Figure 19: original pressure annotations
PressureUS-unit equivalent
Up to 1.38 PaUp to 0.0002 psi
0.345–3.45 kPa0.05–0.5 psi
0.0138–1.38 kPa0.002–0.2 psi
9.65 kPa1.4 psi
1.52–15.2 kPa0.22–2.2 psi
345–517 kPa50–75 psi
Pressure ranges overlap; they are not recast as exclusive groups or assigned exact friction values.
PV AND WEAR PERFORMANCE

PV and Wear Performance

PV is pressure multiplied by velocity. Its limit describes unlubricated continuous operation but does not directly account for wear. Practical conditions must also consider formulation, allowable wear and melting temperature.

Table 6 | PV and wear performance (source reference)
ItemSource FEP15 vol% glass-filled comparison10 vol% bronze-filled comparison
PV limit at 10 fpm6004,5009,000
PV limit at 100 fpm80010,00012,000
PV limit at 1,000 fpm1,0008,00010,000
PV for 0.005 in radial wear in 1,000 h<101,6505,000
Wear factor K, source entries>5,0003010
The source prints PV units as lb/in × fpm, inconsistent with pressure × velocity, and does not clearly state K scaling. Values are retained for comparison, not calculation. The filled controls' base resin is unspecified; they are not identified as Everflon grades.
WEAR FACTOR

Wear Factor

K is a wear proportionality factor for a specified mating surface, without lubrication and below the PV limit.

t=K × P × V × T
Formula symbols and units
SymbolMeaningUnit
tWear depthin
KWear factorin³·min/(lb·ft·hr)
PPressurepsi
VVelocityft/min
TTimehr

Source testing used ambient temperature, unidirectional loading with a fixed bushing or thrust washer, no lubrication and operation below the PV limit. The mating surface was soft carbon steel, source hardness R20–25, finish 12–20 μin AA. The source extends the assessment to many stainless steels and cast irons. Confirm K units and scaling first.

Source data, charts and compliance statements concern another manufacturer’s reference material. Renaming a grade does not establish equivalence or measured performance for Everflon FEP 4610. Curves are approximate illustrations, not engineering input. · Product and Properties Handbook: Hardness; Friction; Pv And Wear Performance; Wear Factor